How To Change Hydraulic Filter On Ford 3000 Tractor

FORD 3000 HOW DO Yous REMOVE THE HYRAULIC FILTER

View previous topic :: View side by side topic
Author	Message
DUCKMEAT New User Joined: twenty Aug 2009 Posts: 15 Written report to Moderator	Posted: Mon Aug 31, 2009 7:32 am   Post subject field: FORD 3000 HOW Practise YOU REMOVE THE HYRAULIC FILTER Tin can SOMEONE Delight TELL ME HOW TO GET TO THE Thing .... THANKS
Back to height
Mathias NY Tractor Expert Joined: 08 Oct 2004 Posts: 1538 Location: Upstate NY Report to Moderator	Posted: Monday Aug 31, 2009 8:59 am   Post subject: Re: FORD 3000 HOW Practice YOU REMOVE THE HYRAULIC FILTER Effort searching a piddling in the archives of the Ford forum. The link beneath is to a tread I started a while ago for the Hydraulics on my 3000. My issue still isn't resolved, but I have narrowed it down to the position/draft command adjustments. To get at both hydraulic filters, drain the fluid, remove the seat, remove the manual top cover, and remove the PTO shaft. I also removed the left floor board, just I can't remember if that was necisary. I also call up there was an access cover on the left side that needed to be removed. The attached picture is of my tractor after I changed both filters. The rear of the tractor is toward the right, the upper arrow is for the outlet filter, and the lower arrow is for the intake filter. Sometime thread
Back to top
DUCKMEAT New User Joined: 20 Aug 2009 Posts: fifteen Written report to Moderator	Posted: Mon Aug 31, 2009 11:24 am   Post subject field: Re: FORD 3000 HOW Do YOU REMOVE THE HYRAULIC FILTER Mathias NY wrote: (quoted from post at 09:59:44 08/31/09) Effort searching a footling in the archives of the Ford forum. The link beneath is to a tread I started a while ago for the Hydraulics on my 3000. My issue nevertheless isn't resolved, but I take narrowed information technology downwards to the position/typhoon control adjustments. To become at both hydraulic filters, drain the fluid, remove the seat, remove the transmission acme cover, and remove the PTO shaft. I also removed the left floor board, but I can't remember if that was necisary. I also think there was an access encompass on the left side that needed to exist removed. The attached picture is of my tractor after I changed both filters. The rear of the tractor is toward the right, the upper arrow is for the outlet filter, and the lower arrow is for the intake filter. Onetime thread Quote: Thanks SO MUCH .. IV TAKEN THAT ROUND Comprehend OFF THE SIDE .. Can I Have THE FILTERS OFF FROM Hither ... AND Volition HY TRAN Piece of work
Back to top
Mathias NY Tractor Good Joined: 08 Oct 2004 Posts: 1538 Location: Upstate NY Report to Moderator	Posted: Monday Aug 31, 2009 12:51 pm   Mail service subject: Re: FORD 3000 HOW Exercise You REMOVE THE HYRAULIC FILTER I don't think it will be possible to remove the filters without removing the pinnacle plate. You will need all the room you lot can go to maneuver the filter assembly around the drive shaft. I was but able to become mine out after removing the PTO shaft and bending the mounting tab on the filter itself. It'southward a very tight fit and unless you have having hydraulic problems, I wouldn't even attempt to clean information technology. Generic Hy-tran might be ok to use. Check the cross reference table on the oil, if the Ford 134 fluid is listed it will be fine. Otherwise, I wouldn't trust it. It sounds like you might be new to working on tractors, I highly recommend buying an owners manual and an I&T service manual. These will exist you best references on using and working on the tractor. Good luck.
Dorsum to top
southern_boy1975 New User Joined: 27 Nov 2017 Posts: 1 Report to Moderator	Posted: Mon November 27, 2017 12:xvi pm   Mail service subject: Re: FORD 3000 HOW DO Y'all REMOVE THE HYRAULIC FILTER Mathias NY wrote: (quoted from mail service at xiii:51:xiii 08/31/09) I don't think it will be possible to remove the filters without removing the top plate. Y'all will demand all the room you tin can become to maneuver the filter associates around the drive shaft. I was only able to become mine out afterward removing the PTO shaft and bending the mounting tab on the filter itself. It's a very tight fit and unless you have having hydraulic bug, I wouldn't even attempt to clean it. Generic Hy-tran might be ok to use. Check the cross reference table on the oil, if the Ford 134 fluid is listed it will be fine. Otherwise, I wouldn't trust it. It sounds like you might be new to working on tractors, I highly recommend buying an owners manual and an I&T service manual. These will exist you all-time references on using and working on the tractor. Good luck. Howdy, yous say they are not worth cleaning without hydraulic problems but what if you are finding a lot of micro metallic particals in the case lesser? I had to remove the side plate to locate part of the pto housing snap band that had broke off. I found a couple of pieces in the rear section and a couple in the hydraulic surface area.. Would you clean them at that point or just wipe the housing out and reassemble? Just looking for opinion..... Thanks
Back to summit
Display posts from previous:

How To Change Hydraulic Filter On Ford 3000 Tractor,

Source: https://forums.yesterdaystractors.com/viewtopic.php?t=525422

Posted by: scottovion1999.blogspot.com

Share this post